What does a hydrogeologist do when a town needs more drinking water? One task might start at a monitoring well, where the hydrogeologist lowers a probe until it touches water. That reading tells them where the water stood in that well at that moment. To advise the town on whether it can pump more, they need to know how water levels change over time, how nearby wells respond to pumping, and whether the water is suitable to drink.
Suppose a town wants to know whether increasing withdrawals from an existing supply well would lower water levels in nearby wells. A hydrogeologist starts by checking well records. A well can be open to water in a shallow layer of sand or in a deeper zone of fractured rock. Two wells close together on a map may take in water from different layers, so their readings may not tell the same story.
At the monitoring well, the hydrogeologist can lower an electric water level tape. When the probe contacts water, the meter signals, often with a beep. The hydrogeologist reads the tape where it crosses a marked point on the well casing and records the depth below that point. Using the same mark on later visits keeps the readings comparable. The notes also include the time and any known nearby pumping. A reading taken while a pump is running can differ from one taken after the pump has been off long enough for the water level to recover.
Repeated visits give a series of snapshots. If the hydrogeologist needs to see what happens between visits, a pressure sensor and data logger can track changes in water level at regular intervals. Those extra readings can show short drops during pumping that a weekly visit might miss.
Back at a computer, the hydrogeologist checks the field notes and puts the measurements on a common elevation reference. Imagine the marked point on one well is 110 meters above sea level and water is 8 meters below it. The water level elevation is 102 meters. At another well, the marked point is 105 meters above sea level and water is 5 meters below it. The water there is at 100 meters elevation. The second well has water closer to its measuring point, but its water level elevation is lower.
With measurements from enough wells open to the same aquifer, taken close together in time, the hydrogeologist can map where water level elevations are higher and lower. An aquifer is a body of rock or sediment that can transmit usable quantities of groundwater. Differences in water level elevation help the hydrogeologist infer which way groundwater tends to move, though features such as fractures can affect the paths it takes. The USGS introduction to groundwater explains how water occupies pores in sediment and cracks in rock.
A graph of water level against time answers a different question: when did the change happen? If a drop begins soon after the supply pump starts and the level rises again after it stops, pumping is a plausible explanation. A single match in timing is not proof. The hydrogeologist looks for a repeated pattern and checks other records, such as rainfall and pumping at other wells.
To separate the effect of the town's pump from background changes, the hydrogeologist may help run a pumping test. The team measures water levels before the test, pumps at a measured rate, and tracks how far water levels fall in the pumped well and in nearby observation wells. The drop from the level before pumping is called drawdown. After the pump stops, the team continues measuring to see how the levels recover.
If an observation well shows drawdown during the test, that is evidence that pumping affects water levels beyond the supply well. The size and timing of the response help the hydrogeologist estimate how readily the aquifer transmits water. A short test, however, cannot show how the supply will behave through a prolonged drought. And even a well that produces plenty of water needs a separate check of water quality. Laboratory tests can measure substances such as nitrate or arsenic, which cannot be judged by how clear the water looks.
The town needs advice it can act on, not just a plot of drawdown. The hydrogeologist might recommend increasing pumping in stages, keeping a gauge in a nearby observation well, and agreeing on a water level that would trigger a review. The report should make clear which effects were measured, which were estimated, and what evidence would change the recommendation.
Earth science and physical geography help you read maps and connect rock layers with groundwater. Algebra and statistics help you compare wells, calculate changes, and judge how much confidence to place in a pattern. Chemistry helps you understand what a laboratory result reports, while physics gives you a way to think about pressure and flow. If your school does not offer earth science, you can still build much of the foundation in those other classes.
Try putting the two example wells into a spreadsheet. Give the measuring point elevation, measured depth, and calculated water level elevation separate columns, with units in the headings. Write one sentence explaining why the shallower reading belongs to the well with the lower water level elevation. The IESC learning resources and earth science practice problems offer other ways to practice working with measurements and explaining your reasoning.
Geology and geoscience are natural starting points if you want to study the rock and sediment that hold groundwater. Environmental science can be a good fit if you are drawn to water quality and the effects of land use. Civil or environmental engineering can build relevant skills if you want to work on wells, pumping systems, or water supply design. Program names vary, so look at the course list rather than relying on the degree title.
Look for groundwater hydrology, field methods, and water chemistry. Courses in geographic information systems, or GIS, help you map wells alongside features such as streams and rock units. Statistics and programming can help you work with long sensor records. When you compare programs, check whether students get to work with real field data. For example, a course that asks you to explain an unexpected well reading gives you a better feel for the job than an exercise where every measurement fits the expected pattern.
Does a hydrogeologist work outside every day?
No. Fieldwork can include measuring wells and collecting samples, while office work includes checking data, making maps, and writing recommendations.
Does a high water level mean a well can supply a lot of water?
Not necessarily. A pumping test shows how much the water level drops at a measured pumping rate, which a single water level reading cannot tell you.
Do I need a degree called hydrogeology?
No. Geology, geoscience, environmental science, and relevant engineering programs can all build useful skills if they offer groundwater coursework and field experience.
About the International Earth Science Competition: an online earth science competition for high school students from around the world. Qualification Round 2027: submissions are open until Sunday, 24 January 2027. How the rounds work